Check out the traffic/transport issues in their route and PLAN AHEAD so that they can be in the college at 08:30AM sharp. This is the MOST IMPORTANT CONDITION for participating in the workshop.
HoD-ECE-SVIT
11P71A0401
|
BOYINA
ABHILASH
|
11P71A0421
|
GANAPATHI
KUVALESH YERLAGADDA
|
11P71A0473
|
ANNADANAM
RUTWIK PRABHAT
|
11P71A0474
|
GANAPA
SAI BINDU
|
11P71A0475
|
M SAI
SANTOSH KUMAR
|
11P71A04A2
|
M SUHA REDDY
|
11P71A04A3
|
G
SUSHMITHA
|
11P71A04A4
|
VELAGALA
VANDANA
|
11P71A04B1
|
ZAHERA
FATIMA
|
11P71A04B3
|
A R S
SASHANK *
|
11P71A0408
|
C ANUSHA
|
11P71A0411
|
GUDA BHANU PRAKASH
|
11P71A0430
|
A N S KARTHIK
|
11P71A0473
|
ANNADANAM RUTWIK PRABHAT
|
11P71A0476
|
ADDAGATLA
SAMANTH KUMAR
|
11P71A0478
|
K SANJAY JI
|
11P71A0495
|
NALLA SOWMYA
|
11P71A04A4
|
VELAGALA VANDANA
|
11P71A04B3
|
A R S SASHANK
|
12P78A0401
|
K. LAKSHMAN
|
1
|
a. It is desired to have a high-gain amplifier
with high input resistance and high output resistance. If a three stage
cascade is used, what configuration should be used for each stage ? Explain.
b.Sketch
the circuit diagram of a cascode amplifier. How do the Av and Ai of this
circuit compare to corresponding values for a common-emitter stage ?
|
|
1
|
Draw the cascade of a common-emitter stage and a common-collector
stage. What are the overall voltage gain, input resistance , and output
resistance of the cascade ?
|
|
1
|
a. For
a capacitively coupled load, is the dc load larger or smaller than the ac
load ?
b. Show
the effect of the capacitively coupled load in terms of the static and
dynamic load lines.
|
|
2
|
a. How
does step-response help in finding the bandwidth of an amplifier ? Explain.
b. Sketch
the frequency response of a single-pole transfer function.
c. Define
fβ and fT and write an equation
which relates the two.
|
|
2
|
a. For
a common-emitter stage , use Miller’s theorem to determine the input
capacitance of a common-emitter stage.
b. How
do coupling and bypass capacitors effect the frequency response of an
amplifier stage ?
|
|
2
|
a. Why
does cascading of stages increase the gain-bandwidth product of an amplifier
?
b. Discuss
the advantages of cascode amplifier.
|
|
3
|
a. Write
the transfer function of an amplifier having three-poles and two finite
zeros.
b. Write
the equations that relate h-parameters to hybrid-π parameters. Show how, at
low frequencies the hybrid-π parameters reduce to h-parameters.
|
|
3
|
a. Draw
the circuit of a single stage RC coupled amplifer and derive the expressions
for the lower cutoff and upper cutoff frequencies .
b. Repeat
(a) with FET amplifer.
|
|
5
|
a. Prove
that negative feedback reduces non-linear distortion.
b. Discuss
the properties of feedback amplifier topologies.
|
|
5
|
a. List
five characteristics of an amplifier that are modified by negative feedback.
b. To
obtain the amplifier without feedback, describe how to obtain the (i) input
circuit and (ii) output circuit
|
|
5
|
a. What
is the difference between global and local feedback ? Show with a circuit.
b. State
the three fundamental assumptions used in the approximate method of analysis
of negative feedback amplifiers.
c. For
each of the four topologies, indicate whether the (i) input impedance and (i)
output impedance increases or decreases as a result of feedback.
|
|
6
|
a. State
the Barkhausen criterion, that is, the conditions necessary for sinusoidal
oscillations to be sustained.
b. What
are the gain margin and phase margin needed to sustained sinusoidal
oscillations ?
c. Sketch
the phase-shift oscillator using a JFET.
|
|
6
|
a. Sketch
the topology for a generalised resonant-circuit oscillator, using impedances
Z1, Z2 and Z3. At what frequency will
the circuit oscillate ? Under what conditions does the configuration reduce
to a Colpitts oscillator ? A Hartley oscillator ?
b. Sketch
the circuit of a Wien bridge oscillator.
Which components determine the frequency of oscillation ? Which
components determine the amplitude of oscillation ?
|
|
6
|
a. Draw
the electrical model of a
piezoelectric crystal. Sketch the reactance versus frequency. Over what
portion of the reactance curve do we desire oscillations to take place when
the crystal is used as part of a sinusoidal oscillator ? Explain.
b. Sketch
a circuit of a crystal-controlled oscillator.
|
|
7
|
a. Derive
an expression for the output power of a class A large-signal amplifier in
terms of Vmax, Vmin, Imax and Imin
b. Discuss
how rectification may take place in a power amplifier.
c. Define
intermodulation distortion and total harmonic distortion.
|
|
7
|
a. Define
(i) class A (ii) class B and (iii)
class AB amplifier
b. Define
conversion efficiency η of a power stage.
c. Draw
the circuit of a class B push-pull power amplifier and state three advantages
of class B over class A.
|
|
7
|
a. Show
that the maximum conversion efficiency of the idealised class B
push-pull circuit is 78.5 pc.
b. Demonstrate
that even harmonics are eliminated in a balanced push-pull amplifier.
|
|
7
|
a. Explain
the origin of crossover distortion. Describe a method to minimise this
distortion.
b. Define
thermal resistance θ. Sketch a dissipation derating curve for power
amplifier. How is θ related to this curve ?
c. What
is a heat sink ? Explain why a heat sink must be used with a power amplifier.
|
|
8
|
a. A
parallel RLC circuit is resonant at 2.7kHz. The circuit has L = 0.15H
inductance, C = 0.232µF,
and parallel resistance of 30,000
ohms.
I.
What is the circuit impedance at resonance ?
II.
What is the circuit Q ?
III.
What is the bandwidth ?
IV.
What is the circuit impedance at the upper
band limit ?
|
|
8
|
a. A
parallel-resonant circuit is resonant at 10MHz, Q = 120, and the resistances
are each 750 ohms. What is the value of Rp and of an equivalent Rs in series
with L which might replace Rp ?
b. A
double tuned circuit k = 2kc and Q1 = Q2 = 80. If f0 = 10.7MHz what are the
frequencies of peak response ? What is the 3-dB bandwidth of the circuit ,
with ripple of 3dB ?
|